This post listed below in relation to Installing A Bathtub is rather entertaining. Don't skip it.
Mounting a bathtub isn't precisely brain surgery, however it does call for solid plumbing, carpentry, and also in some cases, tiling skills. Changing an old bathtub with a new one is also a reasonably difficult job. If the old bathtub is readily available, the job can relocate speedily; if you have to open up a wall surface to remove the old tub as well as place the new tub, the job is a lot harder. In either case, the job is within a house handyman's abilities, although you will need an assistant to vacate the old bathtub and set in the new one. See to it you have actually certified yourself for the task as well as fit trying it. Rather than hiring a professional to take over a halfway-completed job, it is far better to take into consideration using one before you begin. Chances are you might need an expert plumber to make tube links.
This write-up will assist you mount a brand-new bathtub in your restroom if you have currently acquired a new tub as well as do not require to transform the setup of your previous supply of water pipes.
Your devices and also product checklist ought to make up the following:
Getting ready for the Setup
To start with, the sustaining structure supplied with the bath ought to be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to see to it that if the faucet comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you use every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final placement.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is separate the supply of water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be quite bothersome because of the restricted accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth all set for the staying water that will originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this procedure. When the faucets have been removed, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Using both wooden boards under its feet, put the bathtub in the needed position. The wooden boards are handy in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four little points.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the level and changing the feet on the bath tub until the spirit level reviews level.
To set up faucets, fit the bottom of the outermost adaptable tap port to the ideal supply pipe by making a compression sign up with; after that do the same for the other faucet.
Switch on the supply of water and also check all joints as well as brand-new pipework for leakages and tighten them if needed. Load the bathtub and likewise examine the overflow outlet as well as the typical electrical outlet for leaks.
Finally, take care of the bathroom paneling as described in the producer's user's manual. Tiling as well as securing around the bath tub should wait up until the tub has actually been made use of at least once as this will resolve it right into its last position.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the current supply pipes.
If you need to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the supplier given backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The former type ought to be linked to the tap ends first, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split a stiff seal, triggering the water to pass through the wall surface in between the bath and the tiling, leading to difficulties with wetness as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components as well as fittings. They are sold in tubes and also cartridges, and also are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked paper or soft rope. Keep in mind to always load the tub with water before securing, to enable the activity experienced when the bathtub is in use. The sealer can break fairly very early if you do not consider this activity before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally quickly available on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or water-proof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading up on Tools You Need to Install a New Bathtub ? Post feedback directly below. We will be delighted to know your responses about this blog entry. In hopes that you come back again later on. You should take a moment to distribute this blog if you liked it. I treasure reading our article about How to Install a Bathtub.
Visit Our Site